Paradox Accessories

Direct Connect Interface 307

Code: PA1187


  • Incorporates a USB port and a serial port (DB-9)
  • Enables control panel to communicate with a PC at 60m
  • Connect from the control panel’s serial port connector to a PC’s serial (DB-9) or USB port
  • Includes 3 LED status indicators (PC, Panel and RX/TX)
  • Communication speed:38.4k baud (EVO)

2-Way Wireless PGM

Code: PA3710


  • The Two-Way Wireless PGM provides one PGM for the Magellan console with two-way wireless communication between it and the PGM unit with a zone input. Adding to the exceptional security of the Magellan system is the Backup Alarm Reporting Option which allows you to supervise the communication between the Magellan console and the MG-2WPGM.
  • The PGM can be programmed to activate and deactivate (following an event or a delay) through the receiver

PGM4 Expansion Module

Code: PA3806


  • Compatible with Compatible with Spectra SP (V3.00) and Digiplex EVO
  • 4 fully programmable 5A relay outputs
  • Deactivate PGM after event and/or timer
  • Pulse PGM output for fire alarms
  • In-field firmware upgradeable

PGM82 Expansion Module

Code: PA3803


  • Expansion of 8 programmable outputs
  • PGM control via Insite GOLD application
  • PGM control with manual on-box switches
  • Can follow system events
  • Display for each PGM, Data and Power
  • Box cover lock mechanism
  • Supports SP, MG, EVO and Swan
  • Connects to control panel via 4-wire on keypad bus
  • Firmware upgradeable

8 Zone Expansion Module

Code: PA5380


  • Compatible with MG Series, SP Series, and E Series
  • Add 8 zones
  • 1 PGM output
  • Use zone input as an anti-tamper switch input

ZX8 8 Zone Expansion Module

Code: PA3558


  • Compatible with MG Series, SP Series and Digiplex EVO
  • Add 8 zones
  • Selectable input resistors for EOL and Tamper
  • 1 PGM output
  • Use zone input as an anti-tamper switch input
  • Support selectable EOL with V6.0

ZX82 8 Zone Expansion Module

Code: PA5385


  • Expansion of 8 additional zones
  • Supports SP, MG and EVO
  • 4-wire bus connection
  • Status LEDs for zones, power and bus data
  • Enclosure with cover lock mechanism
  • On-board and wall tampers
  • Firmware upgradeable

RTX3 Wireless Expansion Module - REM2

Code: PA3809


  • Compatible with Spectra SP Series and Digiplex EVO
  • 32 wireless zones
  • Maximum number of remote controls: 32
  • Remote control compatibility
  • SP: REM1, REM2, REM3
  • Stand Alone: REM1
  • Wireless PGMs (16 w/SP)
  • Supports two RPT1 and eight K32LRF / K32IRF (Spectra SP only)
  • In-field firmware upgradeable via CV4USB and Winload
  • RF jamming supervision
  • Low battery, tamper and check-in supervision
  • Transmitter signal strength display
  • 3 PGM outputs and 1 optional output
  • Noise level test and indicator


SR130 Wireless Outdoor Siren with Built-in Strobe Light

Code: PA3814

The SR130 is a weatherproof (IP54) and fully supervised wireless siren with a built-in strobe light. SR130 provides fast response to alarm signals with differentiation between intrusion and fire events.


  • Battery operated (3 "C" alkaline batteries) Weather-resistant design with UV protection
  • 2-way, fully supervised communication with the control panel
  • 100dB Piezo siren
  • Separate alarm notifications for intrusion and fire
  • Dual-tamper detection (cover and wall)
  • Squawk functionality
  • Wireless range in a typical residential environment: Up to 70m
  • Strobe lens available in 3 colors (red, blue, and amber)
  • Fully powered using three 1.5 Vdc type "C" alkaline batteries (included)
  • Signal strength/RF transmission and status LED
  • Operating temperature: -25ºC to 55ºC
  • RF frequency: 433MHz or 868MHz
  • Dimensions: 13.4cm x 21.17cm x 5.1cm

RPT1 Wireless Repeater Module

Code: PA3804


  • Built-in transceiver (433MHz or 868MHz)
  • Allows to extend the range of wireless communications
  • Supports all MAGELLAN transmitters
  • Select which zone, PGM and/or keypad signals are repeated
  • Signal strength display
  • 1 programmable 5A relay output
  • Universal transmitter input (N.O./N.C.)
  • In-field firmware upgrade via 307USB and WinLoad
  • Wireless range in a typical residential environment:
    - 75m (240ft) with 433MHz;
    - 50m (160ft) with 868MHz
  • Note: The RPT1 is not supported by the RTX3 when connected to an EVO panel.
  • AC input (16Vac, 20VA)
  • Fits in 20cm x 25.5cm x 7.6cm (8in x 10in x 3in) and 28cm x 28cm x 7.6cm (11in x 11in x 3in) metal boxes

IP150+ Internet Module

Code: PA3805S


  • Central station reporting via IPR512 or IPRS-7
  • Provides connectivity to Insite GOLD, BabyWare, NEware or InField to access your system through the internet
  • DHCP connectivity with no configuration
  • Remote firmware upgrades with a fail-safe mode
  • Sends notification and alarm system events via email
  • Internal diagnostic logs via Insite GOLD app
  • SSL support for sending secured email messages, via a secure sockets layer; a popular protocol for encrypting information over the internet
  • Easy installation: no screws needed, a built-in clip for mounting in a metal box

PCS250 GPRS/GSM Communicator Module

Code: PA3816S


  • Compact, sleek design
  • Report events to the IPR512 GPRS/IP Monitoring Receiver and/or IPRS-7 IP/GPRS PC Receiver Software
  • Report via text message (up to 16 cell phone numbers)
  • Control panel communication supervision
  • End-user can arm or disarm the system by sending a text message (SMS) to the PCS250
  • Send pre-recorded voice messages to up to 8 telephone numbers to report alarms using the optional VDMP3 Paradox Plug-in Voice Module (GSM mode)
  • Simple installation with 4-wire serial connection
  • Optional rod antenna can be installed up to 18m (60ft) from the module using optional antenna cable extensions depending on the local signal strength
  • 128-bit (MDS) and 256-bit (AES) encryption (GPRS mode)
  • Increase the distance between the panel and the PCS250 module with an RS485 link (GSM mode only via e-bus). A CVT485 module must be added to the panel in order to accomplish this
  • Report via GSM (CID, SIA)
  • EN 50131 grade 3

HUB2 Hub and Bus Isolator

Code: PA5363


  • Divide the bus into two completely isolated outputs (if one output fails, the other will continue to function)
  • One input port, 2 completely isolated output ports
  • Each output port provides communications up to 900m

Switching Power Supply

Code: PA1650


  • 13.8Vdc, 1.75A switching power supply
  • Fuseless electronic protection with automatic restore
  • Automatic transfer to backup battery power
  • Second backup battery connector (optional)
  • Battery test input

PS17 Digiplex Power Supply Module

Code: PA3462


  • 1.7A switching power supply
  • Fully supervised (AC, battery, low battery and auxiliary limit)
  • Selectable battery charge current (350mA/850mA)
  • 1 PGM output
  • Includes 20cm x 25.5cm x 7.6cm metal box


Paradox Remotes

Hand-Held Two-Way Remote Keypad

Code: PA3712


  • Compatible with MG5050, MG6250, and Spectra SP series V3.00 (or higher) and RTX3 V1.31 (or higher)
  • Supports StayD
  • System Status Memory: The REM3 will keep the last system status received from the control panel in memory. Momentarily press the Info button to display the last system status--even when out of range. Used to confirm the last action you did on the system while away from the system.
  • Configure which partitions the REM3 arms/disarms
  • Built-In Transceiver (433MHz or 868MHz)
  • Independent Arm, Sleep, Stay and Off buttons and LED display per partition
  • Control up to 6 PGMs and/or generate panics
  • Keypad Mode: Requires code entry
  • Remote Mode: One-touch arming / Disarming
  • Installer Diagnostic Mode:
    - Partition 1 LEDs = Signal Strength Display
    - Partition 2 LEDs = RF Interference Display
  • Provides visual and auditory feedback of system status
  • Press the Status button to receive system status
  • Label to identify remote control owner
  • Compact, water-resistant design
  • Size: 8cm x 3.4cm x 1.5cm

2-Way Remote Control with Backlit Buttons

Code: PA3705


  • Supports StayD Mode
  • System Status Memory: The REM2 will keep the last system status received from the control panel in memory. Momentarily press the Info button to display the last system status-even when out of range. Used to confirm the last action you did on the system while away from the system.
  • Built-in transceiver (433MHz or 868MHz)
  • Displays system status using visual (LED) and auditory feedback
  • Press the Status button at any time to receive the system status
  • Perform up to 6 different actions per remote control
  • Compact, water-resistant design with backlight for buttons
  • Wireless range in a typical residential environment:
    - 45m with MG5050 / RTX3

Remote Control with Backlit Buttons

Code: PA3711


  • Slim, ergonomic design
  • Water resistant
  • Perform up to 5 different actions
  • Wireless range in a typical residential environment:
    - 45m (150ft) with MG5050
    - 60m (200ft) with RTX3
  • Available in 433MHz or 868MHz

Emergency/Panic Remote Control with Bracket

Code: PA3714


  • Water resistant
  • Panic function allows user to instantly send panic signal to monitoring station
  • Manually-activated battery test function
  • Visual indicator (LED) for arming actions and battery testing
  • Includes lanyard attachment to facilitate portability; optional wrist strap and belt clip also available
  • Includes easily-replaceable CR2032 battery, with a battery life of 3 years
  • Available in 2 colors: black and white
  • Wireless range in a typical residential environment:
    - 30m (100ft) with MG6250
    - 45m (150ft) with MG5050
    - 60m (200ft) with RTX3
  • Available in 433 or 868 MHz
  • Accessory: wall mount bracket for installation on flat surfaces




Do not hesitate contact the Spectrum Security Products Sales Team for more information or to place your order.


Best Prices | Largest Selection | Finest Technology | Communications Leaders